Alloy Artifacts

Exploring Ingenuity in Iron ...

Alloy Artifacts Home

J.H. Williams, The SuperCompany


Table of Contents

Introduction

Company History


Patents

Table 1. J.H. Williams & Co.: Issued and Licensed Patents
Patent No.InventorFiledIssuedDescriptionExamples
247,987 W.H. Brock08/05/188110/04/1881Chain Pipe Wrench Williams No. 0 Chain Wrench
250,641 W.H. Brock11/02/188112/13/1881Chain Pipe Wrench Williams No. 0 Chain Wrench
254,862 W.H. Brock02/09/188203/14/1882Chain Pipe Wrench Williams No. 0 Chain Wrench
298,442 W.H. Brock02/02/188405/13/1884Chain Pipe Wrench Williams No. 0 Chain Wrench
377,795 J.H. Williams05/23/188702/14/1888Chain Pipe Wrench Williams No. 0 Chain Wrench
RE11,277 H. Hammond07/18/189210/18/1892Adjustable Wrench  
570,213 G. Amborn, Jr.04/06/189610/27/1896Chain Pipe Wrench  
570,214 G. Amborn, Jr.06/01/189610/27/1896Chain Pipe Wrench  
577,653 W.J. Grinden & G. Amborn, Jr.04/01/189602/23/1897Chain Pipe Wrench  
577,654 W.J. Grinden & G. Amborn, Jr.04/01/189602/23/1897Chain Pipe Wrench  
D35,385 G. Amborn, Jr.07/22/190112/03/1901Pipe Wrench  
697,977 G.W. Bufford01/27/190204/22/1902Pipe Wrench  
876,925 G. Amborn03/08/190701/21/1908Chain Pipe Wrench  
876,926 G. Amborn05/06/190701/21/1908Chain Pipe Wrench ["Bijaw"] Vulcan No. 30 "Bijaw" Chain Pipe Wrench
956,259 G. Amborn02/11/190804/26/1910"Ratcho" Open-End Wrench Williams "Ratcho" Ratcheting Open-End Wrench
D46,260 C.A. Martin06/04/191408/11/1914Spanner Wrench  
D46,782 F.W. Trabold10/23/191412/15/1914Automobile Tire Tool  
1,239,459 A.F. Carew11/30/191509/11/1917Tool and Tool Holder  
1,327,309 G.W. Bufford03/14/191801/06/1920Chain Pipe Wrench  
1,778,748 L.G. Bayrer04/14/192310/21/1930Pipe Wrench  
1,787,787 W.C. Kress07/24/192501/06/1931Pipe Vise  
1,810,108 W.C. Kress08/22/192906/06/1931Holder for Wrench Set  
1,811,137 W.C. Kress01/15/193006/23/1931Multi-Socket Wrench Williams No. 1999 Multi-Socket Wrench
1,889,203 W.C. Kress06/14/192911/29/1932Holder for Wrench Set  
1,954,820 W.C. Kress09/20/193204/17/1934Wrench  
1,957,462 W.C. Kress01/25/193305/08/1934Ratchet Wrench Williams S-51 Ratchet
2,071,543 W.C. Kress09/14/193302/23/1937Revolving Grip Handle Williams NM-110 Drive Handle
2,097,594 W.C. Kress05/18/193611/02/1937Reversible Ratchet Wrench  
2,112,840 F.A. Haist05/08/193504/05/1938Method of Making Adjustable Wrenches Williams AP-8 Adjustable Wrench
2,167,720 W.C. Kress03/18/193708/01/1939Torque Indicating Wrench  
2,407,558 W.C. Kress11/16/194409/10/1946Ratchet Adapter  
2,444,135 W.C. Kress01/31/194406/29/1948Worm Joint Pliers  
2,600,617 C.F. Coates12/01/194806/17/1952Adjustable Crowfoot Wrench Williams SC-8 Adjustable Crowfoot
2,719,449 W.J. Johnson07/27/195310/04/1955Adjustable Wrench Locking Mechanism Williams APL-6 Adjustable Wrench
2,772,763 W.J. Johnson01/12/195112/04/1956Dual-Pawl Ratchet Mechanism Williams S-52 Ratchet

Trademarks

Williams registered a number of trademarks, including the W-Diamond logo, "Williams", "Agrippa", "Vulcan", "Superrench", and "Superratchet".


Manufacturing Dates

Williams tools are generally not marked with a date code or other explicit indication of the manufacturing date. When an estimate of the manufacturing date is needed, it will have to be based on other information such as company name markings, tool design style, patent markings, and other factors.

In order to assist with estimating manufacturing dates, we hope to develop some guidelines based on tool markings and other characteristics. For now, the following list of events and observations may be helpful in determining the manufacturing date for some tools.

  • W-Diamond Logo. The Williams W-Diamond logo was registered as a trademark, with the first use listed as 1884.
  • Brooklyn Marking. The company moved its headquarters from Brooklyn to Buffalo (New York) some time after 1919.
  • Williams Scroll Logo. The Williams name underlined by the "S" was registered as a trademark, with the first use listed as 1924. The initial use on wrench faces included a W-Diamond logo below the scroll, with "Forged in U.S.A." or similar text.
  • Superrench Trademark. The "Superrench" trademark was registered in 1925.
  • NX Series of 1 Inch Drive Tools. In the late 1930s Williams introduced 1 inch (square) drive tools in the NX series, a replacement for older hex drive tools.
  • NM Series of 1/4-Drive Tools. In 1940 Williams introduced 1/4-drive tools in the NM- series as a replacement for 9/32 drive.
  • Cadmium Finish During Wartime Years. Due to material shortages during the 1941-1945 wartime years, the standard chrome plated finishes were replaced with cadmium plating or plain steel.
  • "Williams U.S.A." Logo on Wrench Faces. Around 1947 the wrench face markings were updated to use the Williams scroll with "U.S.A." below, replacing the older W-Diamond logo. The W-Diamond logo continued to be marked on some tool shanks, but no longer appeared on wrench faces.
  • Double-Groove Style for Sockets. The double-groove style for sockets (see for example the 1/2-Drive Double-Groove Sockets) was introduced around 1948.
  • Ribbed-Style Open-End Wrenches. The "ribbed" style for open-end wrenches was introduced in 1952. This style remained in use until around 1960, when it was replaced by the flat shank style.
  • Raised Panels on Wrenches. The raised-panel wrench style was introduced around the mid 1950s, some time after the 1952 advent of the ribbed style.
  • Flat Shanks on Wrenches. The wrench style with flat shanks had been introduced by 1960.
  • Cross-bar Holes with 1/2-Drive Deep Sockets. The SD-12xx series deep sockets were fitted with cross-bar holes until at least the mid 1950s, but by 1960 cross-bar holes had been discontinued.
  • Cold-formed Sockets. By the mid 1970s Williams was using a cold-forming process (called "Impact Extruded" in the catalog) for making sockets in 3/8 through 1 inch drive sizes.

Face Markings on Wrenches

Williams changed the style of the face markings on its wrenches several times over the years, and these markings therefore provide an approximate guide to the manufacturing date.

[Williams Early Brooklyn Face Markings]
Fig. 1. Williams Early "Brooklyn" Face Markings.

Fig. 1 shows an example of one of the earliest face markings, consisting the text "J.H. Williams & Co." and "Bklyn, N.Y. U.S.A.", typically stamped on the face of a wrench. Tools bearing this face marking generally also have a W-Diamond logo forged into the shank.

This marking is believed to have been used on early production, when the Brooklyn address referred to both the company's headquarters and its principal factory location. This mark will be referred to in the text as the early Brooklyn face marking.

[Williams Oval Brooklyn Face Markings]
Fig. 2. Williams Oval "Brooklyn" Face Markings.

Fig. 2 shows the first of a pair of similar markings, consisting of an oval outline with the text "J.H. Williams & Co." and "Brooklyn, U.S.A.", with the W-Diamond logo in the center. On smaller tools, the text was generally abbreviated further to fit in the available space.

As the Brooklyn address suggests, this marking was used while the company was located in Brooklyn, New York. This mark will be referred to in the text as the JHW-Brooklyn logo.

[Williams Oval Forged Logo]
Fig. 3. Williams Oval "Forged" Face Markings.

Fig. 3 shows the very similar oval outline with the text "J.H. Williams & Co." and "Forged in U.S.A.", again with the W-Diamond logo in the center.

This marking may have been used to distinguish production at the Buffalo factory (or other facilities) from the main Brooklyn factory and headquarters. Williams built its Buffalo factory in 1914, but the company headquarters were still in Brooklyn as late as 1919. This mark will be referred to in the text as the JHW-Forged logo.

[Williams Forged in U.S.A. Face Markings]
Fig. 4. Williams "Forged in U.S.A." Face Markings.

Around 1924 Williams updated its wrench face markings to the style shown in Fig. 4 at the left. The Williams name is underlined by a scroll from the terminal "S", and the text "Forged in U.S.A." appears below, with the W-Diamond logo in the center. The 1924 date is based on the trademark registration for the Williams name with the scroll underline, which lists 1924 as the first use date.

Several alternate forms of this style were used for smaller tools with insufficient space for the full "Forged in U.S.A." text. These alternates (in order of decreasing size) used the text "Made in U.S.A.", then "Made U.S.A.", and finally just "U.S.A." for the smallest tools. Examples of these markings can be found at various places in this article.

[Williams U.S.A. Face Markings]
Fig. 5. Williams "U.S.A." Face Markings.

By 1947 Williams had updated its wrench face markings to the simpler style shown in Fig. 5 at the left. The Williams name remained underlined by a scroll, but the text below was simply "U.S.A." without the W-Diamond logo. (This example is highly polished, and the reflection made it a bit difficult to photograph.)

This style of marking was generally used on wrench faces from about 1947 until around 1955, after which the adoption of the ribbed wrench style forced the markings to move to the shank. This marking was also used on tools without a well-defined "face", being placed on the shank or some other part of a tool. We'll refer to this as the "Williams U.S.A." marking in the text.


Early Tools and Carbon-Steel Wrenches

The early tools produced by Williams were generally marked with the JHW-Brooklyn logo, an oval outline enclosing "J.H. Williams & Co." and "Brooklyn, U.S.A.", with the familiar W-Diamond logo in the center. In some cases only the W-Diamond logo was marked on the tool.


No. 0 Brock Patent Chain Wrench

J.H. Williams became an early leader in the market for chain pipe wrenches, and developed or licensed a number of patents for such tools. We'll begin this section with an early example of one of their chain wrenches.

[Williams No. 0 Brock Patent Chain Wrench]
Fig. 6. Williams No. 0 Brock Patent Chain Wrench, with Inset for Side View, ca. 1888-1895.

Fig. 6 shows an early Williams No. 0 chain wrench, marked with the W-Diamond logo and "Brock Chain Wrench" on the face plate, and with "Made By J.H. Williams & Co" and "Brooklyn, N.Y. U.S.A." forged into the handle.

The overall length is 12.5 inches, and the finish is plain steel.

The face plate also lists no fewer than five patent dates, which must be something of a record. The dates and patents are Oct. 4, 1881 (Brock, #247,987), Dec. 13, 1881 (Brock, #250,641), Mar. 14, 1882 (Brock, #254,862), May 13, 1884 (Brock, #298,442). and Feb. 14, 1888 (Williams, #377,795).


Vulcan No. 30 Bijaw Chain Pipe Wrench

[Williams No. 0 Brock Patent Chain Pipe Wrench]
Fig. 7. Williams No. 30 Vulcan Chain Pipe Wrench, with Inset for Side View, ca. 1908-1920.

Fig. 7 shows a later Vulcan No. 30 "Bijaw" chain pipe wrench, marked "J.H. Williams & Co" and "Brooklyn, N.Y. U.S.A." with the W-Diamond logo forged into the face plate. The face is also marked with a "Pat'd in U.S. Jan. 21 08" and several foreign patent notices.

The overall length is 13.7 inches, and the finish is plain steel.


Open-End Wrenches

Open-end wrenches were among the early tools produced by J.H. Williams, and the model numbering system developed for open-end wrenches became widely adopted by the industry.


"White" No. 729 Open-End Wrench

[Williams No. 729 5/8x3/4 Open-End Wrench]
Fig. 8A. Williams "White" No. 729 5/8x3/4 Open-End Wrench.

Fig. 8A shows an early Williams No. 729 5/8x3/4 open-end wrench, apparently made for the White company (possibly the truck manufacturer). The face is stamped "J.H. Williams & Co." and "Bklyn. N.Y. U.S.A." on one end with the 729 model number on the other, and the "White" name is engraved in script on the shank. The shank also has a forged-in "29" and a W-Diamond logo, but the latter has been partially ground off.

The overall length is 6.9 inches, and the finish is plain steel.

The reverse faces are stamped "7/16" and "1/2", references to the older S.A.E. size convention.


Early No. 731B Open-End Wrench

[Williams No. 731B 13/16x7/8 Open-End Wrench]
Fig. 8B. Williams No. 731B 13/16x7/8 Open-End Wrench, with Inset for Side View.

Fig. 8B shows an early Williams No. 731B 13/16x7/8 open-end wrench, stamped "J.H. Williams & Co." and "Bklyn, N.Y. U.S.A." on one face with the model number on the other end. The shank also has a forged-in W-Diamond logo at the left.

The overall length is 7.8 inches, and the finish is plain steel.

The reverse faces are stamped "9/16" and "5/8", references to the older Hex Capscrew size convention.


No. 723A "Pierce-Arrow" Open-End Wrench

We'll now turn to some early wrenches marked with the JHW-Brooklyn logo.

[Williams No. 723A Pierce-Arrow 3/8x1/2 Open-End Wrench]
Fig. 9. Williams No. 723A "Pierce-Arrow" 3/8x1/2 Open-End Wrench.

Fig. 9 shows an early Williams No. 723A 3/8x1/2 open-end wrench, stamped with the JHW-Brooklyn logo on the face, with the industry-standard model number on the other face. The reverse shank is stamped with the "Pierce-Arrow" logo, indicating that this wrench was contract production for the Pierce company.

The overall length is 3.9 inches, and the finish is plain steel with polished faces.

The reverse faces are stamped "3/16" and "5/16", references to the older Hex Cap Screw size convention.


No. 725 Open-End Wrench

[Williams No. 725 7/16x1/2 Open-End Wrench]
Fig. 10. Williams No. 725 7/16x1/2 Open-End Wrench.

Fig. 10 shows an early Williams No. 725 7/16x1/2 open-end wrench, stamped with the JHW-Forged logo on the face, but with the company name in the "J.H.W. abbreviated form. The reverse face is stamped with the industry-standard model number, but the opening sizes are not marked.

The overall length is 4.8 inches, and the finish is plain steel with polished faces.


No. 29 Open-End Wrenches

The next figures show two examples of early No. 29 wrenches.

[Williams No. 29 11/16x25/32 Open-End Wrench]
Fig. 11. Williams No. 29 11/16x25/32 Open-End Wrench, with Inset for Reverse Detail.

Fig. 11 shows an early Williams No. 29 11/16x25/32 open-end wrench, stamped with the JHW-Forged logo on one face. The shank has the W-Diamond logo forged into one side, with the industry-standard model number 29 forged into the reverse, as shown in the inset.

The overall length is 6.8 inches, and the finish is plain steel.

The reverse faces are marked "3/8" and "7/16", references to the older U.S.S. size convention.

[Williams No. 29 11/16x25/32 Open-End Wrench]
Fig. 12. Williams No. 29 11/16x25/32 Open-End Wrench.

Fig. 12 shows a somewhat later Williams No. 29 11/16x25/32 open-end wrench, stamped with the JHW-Brooklyn logo on one face, with the model number stamped on the other end.

The overall length is 6.9 inches, and the finish is plain steel.


No. 35 Open-End Wrench

[Williams No. 35 31/32x1-1/16 Open-End Wrench]
Fig. 13. Williams No. 35 31/32x1-1/16 Open-End Wrench.

Fig. 13 shows an early Williams No. 35 31/32x1-1/16 open-end wrench, stamped with the JHW-Brooklyn logo on the face, and with the W-Diamond logo forged into the shank. The industry-standard model number is forged into the reverse side of the shank, as shown in the inset.

The overall length is 9.7 inches, and the finish is plain steel.

The reverse faces are marked "9/16" and "5/8", references to the older U.S.S. size convention.


No. 731 Open-End Wrench

This next figure shows a variant of the J.H. Williams oval logo, with "Forged in U.S.A." replacing "Brooklyn, U.S.A." along the botton edge.

[Williams No. 731 3/4x13/16 Open-End Wrench]
Fig. 14. Williams No. 731 3/4x13/16 Open-End Wrench.

Fig. 14 shows an early Williams No. 731 3/4x13/16 open-end wrench, marked with the W-Diamond logo forged into the shank, and with the "Forged in U.S.A." variant of the JHW-Brooklyn logo on one face. The industry-standard model number 731 is stamped on the other front face.

The overall length is 7.8 inches, and the finish is plain steel.

The reverse faces are marked "1/2" and "9/16", references to the older U.S.S. size convention.

The use of a stamped rather than forged-in model number suggests later production than the previous example. The "Forged" variant of the oval logo is believed to indicate production in the new Buffalo factory, but before the company headquarters were moved to that location.


No. 737 Open-End Wrench

[Williams No. 737 1-1/8x1-1/4 Open-End Wrench]
Fig. 15. Williams No. 737 1-1/8x1-1/4 Open-End Wrench, with Inset for Marking Detail.

Fig. 15 shows an early Williams No. 737 1-1/8x1-1/4 open-end wrench, stamped with the "Forged in U.S.A." variant of the JHW-Brooklyn logo on the face, and with a W-Diamond logo forged into the shank. The industry-standard model number 737 is stamped on the reverse face (not shown).

The overall length is 11.6 inches, and the finish is plain steel.


1474 Open-End Wrench

[Williams 1474 5/8x11/16 Open-End Wrench]
Fig. 16. Williams 1474 5/8x11/16 Open-End Wrench.

No. 30 Open-End Wrench

Later carbon-steel wrenches were marked with the Williams scroll and W-Diamond logos.

[Williams No. 30 11/16x7/8 Open-End Wrench]
Fig. 17. Williams No. 30 11/16x7/8 Open-End Wrench, ca. 1924-1947.

Fig. 17 shows a Williams No. 30 11/16x7/8 open-end wrench, stamped on the face with "Forged in U.S.A." and the W-Diamond logo.

The overall length is 8.5 inches, and the finish is plain steel with traces of black paint on the shank.

The reverse faces are marked with the fractional sizes of the openings.


No. 31 Open-End Wrench

[Williams No. 31 25/32x7/8 Open-End Wrench]
Fig. 18. Williams No. 31 25/32x7/8 Open-End Wrench, ca. 1924-1947.

The overall length is 9.1 inches, and the finish is plain steel with traces of black paint on the shank.


Single-Open Engineer's Wrenches

Single-open "Engineer's" wrenches were actually the first tools offered by Williams, at least if we use the model numbers as a guide. When the numbering system was laid out, single-open wrenches for U.S.S. bolts were assigned numbers 1 through 20, with the U.S.S. double-open wrenches picking up at number 21. A second series of single-open wrenches for the Hex Cap Screw sizes was introduced later, with model numbers running in a 700 series.


No. 3 Single-Open Engineer's Wrench

[Williams No. 3 11/16 Single-Open Engineer's Wrench]
Fig. 19. Williams No. 3 11/16 Single-Open Engineer's Wrench.

Fig. 19 shows an early Williams No. 3 11/16 single-open wrench, stamped with the JHW-Brooklyn logo on the face, and with the W-Diamond logo forged into the shank.

The overall length is 5.6 inches, and the finish is plain steel.


704 Single-Open Engineer's Wrench

[Williams No. 704 3/4 Single-Open Engineer's Wrench]
Fig. 20. Williams No. 704 3/4 Single-Open Engineer's Wrench, ca. 1924-1947.

Fig. 20 shows a later Williams No. 704 3/4 single-open wrench, stamped "Forged in U.S.A." with the W-Diamond logo on the face, and with the model number stamped into the shank.

The overall length is 7.2 inches, and the finish is plain steel with traces of the original black paint.


Textile-Pattern Wrenches

The next figures show examples of textile-pattern open-end wrenches, tools that were often used for servicing looms and other textile machinery.


Early 761 Special Textile-Pattern Open-End Wrench

[Williams 761 Special 7/16x1/2 Textile-Pattern Open-End Wrench]
Fig. 21. Williams 761 Special 7/16x1/2 Textile-Pattern Open-End Wrench, with Insets for Marking Detail.

Fig. 21 shows an early Williams 761 Special 7/16x1/2 textile-pattern wrench, stamped "J.H. Williams & Co." and "Bklyn, N.Y. U.S.A." on one face, with "Special" on the other face. The shank has a forged-in W-Diamond logo and is also stamped "S.L.S.", and the reverse has a forged-in "761" model number.

The overall length is 5.7 inches, and the finish is plain steel.


761C Textile-Pattern Open-End Wrench

[Williams 761C 19/32x11/16 Textile-Pattern Open-End Wrench]
Fig. 22. Williams 761C 19/32x11/16 Textile-Pattern Open-End Wrench, with Inset for Reverse Detail.

Fig. 22 at the left shows an early Williams 761C 19/32x11/16 textile-pattern wrench, stamped "J.H. Williams & Co." and "Bklyn, N.Y. U.S.A." on the face, with the W-Diamond logo forged into the shank.

The overall length is 5.7 inches, and the finish is plain steel.

The reverse faces are marked "5/16" and "3/8", references to the older U.S.S. size convention.


762 Special "Johnson & Basgett" Textile-Pattern Open-End Wrench

[Williams 762 Special Johnson & Basgett Textile Wrench]
Fig. 23. Williams 762 Special "Johnson & Basgett" Textile Wrench, with Inset for Reverse Detail.

Fig. 23 shows a rare Williams 762 "Special" textile-pattern wrench with measured sizes 5/8x23/32, stamped on the face "Forged in U.S.A." with the W-Diamond logo. The reverse shank is stamped "Johnson & Basgett", presumed to be the customer for this special-order wrench.

The overall length is 7.0 inches, and the finish is plain steel.


762C Textile-Pattern Open-End Wrenches

The next figures show two generations of the Williams 762C textile wrench.

[Williams 762C 11/16x7/8 Textile-Pattern Open-End Wrench]
Fig. 24. Williams 762C 11/16x7/8 Textile-Pattern Open-End Wrench, with Inset for Reverse Detail.

Fig. 24 at the left shows an early Williams 762C 11/16x7/8 textile-pattern wrench, stamped "J.H. Williams & Co." and "Bklyn, N.Y. U.S.A." on the face, with the W-Diamond logo forged into the shank.

The overall length is 6.9 inches, and the finish is plain steel.

The reverse faces are stamped "3/8" and "1/2", references to the opening sizes in the old U.S.S. size convention.

[Williams 762C 11/16x7/8 Textile-Pattern Open-End Wrench]
Fig. 25. Williams 762C 11/16x7/8 Textile-Pattern Open-End Wrench.

Fig. 25 at the left shows a later Williams 762C wrench, stamped "Forged in U.S.A. on the face with the W-Diamond logo.


Toolpost Wrenches


525 Toolpost Wrench

[Williams 525 1/4x5/16 Toolpost Wrench]
Fig. 26. Williams 525 1/4x5/16 Toolpost Wrench, with Inset for Reverse Detail.

Fig. 26 at the left shows a Williams 525 1/4x5/16 toolpost wrench, marked with the W-Diamond logo forged into the shank, and with the abbreviated variant of the JHW-Brooklyn logo stamped on the face.

The overall length is 3.9 inches.


529 Toolpost Wrenches

[Williams 529 3/8x7/16 Toolpost Wrench]
Fig. 27. Williams 529 3/8x7/16 Toolpost Wrench, with Insets for Marking Detail.

Fig. 27 at the left shows an early Williams 529 3/8x7/16 toolpost wrench, marked with the W-Diamond logo forged into the shank, and with the abbreviated variant of the JHW-Brooklyn logo stamped on the face.

The overall length is 5.8 inches. The finish is plain steel with some traces of the original black paint.


[Williams 529 3/8x7/16 Toolpost Wrench]
Fig. 28. Williams 529 3/8x7/16 Toolpost Wrench.

Fig. 28 shows a later Williams 529 3/8x7/16 toolpost wrench, marked with the W-Diamond logo forged into the shank, and with "Made U.S.A." and the W-Diamond logo stamped on the face.

The overall length is 5.7 inches, and the finish is plain steel.


556 Toolpost Wrench

[Williams 556 5/8 Open-Box Toolpost Wrench]
Fig. 29. Williams 556 5/8 Open-Box Toolpost Wrench, with Inset for Side View.

Fig. 29 shows a Williams 5/8 toolpost wrench in the open-box style, marked with a variant of the JHW-Brooklyn logo with abbreviated names.

The overall length is 6.8 inches, and the finish is plain steel.

The top inset shows a side view of the wrench, illustrating the massive construction typical for this type of tool.


Check-Nut Wrenches

Check-nut wrenches were the forerunners of the modern tappet wrench, a type of thin open-end wrench designed to service opposing nuts on a variety of machinery.

Single-ended check-nut wrenches were being offered as early as 1901 in the Tenth Edition catalog. Wrenches as that time were available in models ranging from No. 602 (5/16 U.S.S.) up to No. 610 (1 Inch U.S.S.).


624 Check-Nut Wrench

[Williams 624 13/32x19/32 Check-Nut Wrench]
Fig. 30. Williams 624 13/32x19/32 Open-End Wrench.

Fig. 30 shows a Williams 624 13/32x19/32 check-nut wrench, stamped "J.W.H. & Co." in a variant JHW-Brooklyn logo on one face. The shank has a depressed panel with "Check Nut Wrench" and a raised W-Diamond logo at the end, and the reverse has the forged-in "624" model number.

The overall length is 4.3 inches, and the finish is plain steel.

The reverse faces are marked "3/16" and "5/16", references to the wrench sizes in the U.S.S. convention.


632 Check-Nut Wrench

[Williams 632 25/32x31/32 Check-Nut Wrench]
Fig. 31. Williams 632 25/32x31/32 Open-End Wrench.

Fig. 31 shows a Williams model 632 check-nut wrench with sizes 25/32 and 31/32, marked with the JHW-Brooklyn logo on one face. The shank has several forged-in markings, including the "632" model number at one end, a depressed panel with "Check Nut Wrench" in the center, and the W-Diamond logo at the other end.

The overall length is 8.4 inches, and the finish is plain steel.

The reverse faces are marked "7/16" and "9/16", references to the wrench sizes in the U.S.S. convention.


635E Check-Nut Wrench

[Williams 635E 1x1-1/4 Check-Nut Wrench]
Fig. 32. Williams 635E 1x1-1/4 Check-Nut Wrench, with Inset for Marking Detail.

Fig. 32 shows a Williams 665E 1x1-1/4 check-nut wrench, marked with the JHW-Brooklyn logo stamped on the face. The shank is marked with "Check Nut Wrench" forged into a depressed panel, and the model number and W-Diamond logo are forged into the ends of the shank. (The "E" suffix of the model is stamped, indicating that the wrench blank could be used for multiple sizes.)

The overall length is 10.4 inches, and the finish is plain steel, possibly with black paint originally.

The reverse faces are marked "3/4" and "1", apparent references to the older "Hex Cap Screw" size convention.


633 Mack Check-Nut Wrench

[Williams 633 7/8x1 Mack Check-Nut Wrench]
Fig. 33. Williams 633 7/8x1 Mack Check-Nut Wrench.

Fig. 33 shows a much later example of the check-nut wrench series, a Williams 633 7/8x1 check-nut wrench made for Mack.


S-Shaped Wrenches


662D S-Shaped Wrench

[Williams 662D 7/16x1/2 S-Shaped Wrench]
Fig. 34. Williams 662D 7/16x1/2 S-Shaped Wrench.

Fig. 34 shows a Williams 662D 7/16x1/2 S-shaped wrench, marked with the JHW-Brooklyn logo. The overall length is 4.9 inches.

This wrench has an unusually clear "Brooklyn" logo, so this image was used for our table of logos.


662F S-Shaped Wrench

[Williams 662F 1/2x9/16 S-Shaped Wrench]
Fig. 35. Williams 662F 1/2x9/16 S-Shaped Wrench.

Fig. 35 at the left shows a Williams 662F 1/2x9/16 S-shaped wrench, stamped "Made U.S.A." with the W-Diamond logo on the face.

The overall length is 5.0 inches, and the finish is plain steel.

The reverse is marked with a forged-in "T" code.


663E S-Shaped Wrench

[Williams 663E 9/16x3/4 S-Shaped Wrench]
Fig. 36. Williams 663E 9/16x3/4 S-Shaped Wrench.

Fig. 36 at the left shows a Williams 663E 9/16x3/4 S-shaped wrench, stamped "Forged in U.S.A." with the W-Diamond logo on the face.

The overall length is 6.2 inches, and the finish is black paint with polished faces.

The reverse faces are stamped "3/8 S.A.E." and "1/2 S.A.E.", references to the older size convention.


664A S-Shaped Wrenches

The next figures show two versions of the Williams 664A S-shaped wrench.

[Williams 664A 11/16x7/8 S-Shaped Wrench]
Fig. 37A. Williams 664A 11/16x7/8 S-Shaped Wrench, with Inset for Reverse Detail.

Fig. 37A at the left shows a Williams 664A 11/16x7/8 S-shaped wrench, marked with the JHW-Brooklyn logo on one face, and with the W-Diamond logo forged into the shank.

The overall length is 7.5 inches, and the finish is plain steel.

The inset shows the forged-in "664" in the reverse with a stamped "A" code.

[Williams 664A 11/16x7/8 S-Shaped Wrench]
Fig. 37B. Williams 664A 11/16x7/8 S-Shaped Wrench, with Inset for Reverse Detail.

Fig. 37B shows a very similar Williams 664A S-shaped wrench, but stamped with the JHW-Forged logo instead of the Brooklyn variant. The "664" base model number is forged into the shank with the "A" suffix stamped, and with the W-Diamond logo forged into the other end.

The overall length is 7.5 inches, and the finish is plain steel.

The inset shows a close-up of the stamped JHW-Forged logo.


683A S-Shaped Wrench

[Williams 683A 15/16x1 S-Shaped Wrench]
Fig. 38. Williams 683A 15/16x1 S-Shaped Wrench, with Inset for Reverse Detail.

Fig. 38 at the left shows a Williams 683A 15/16x1 S-shaped wrench, stamped with the JHW-Brooklyn logo on one face, and with "683" and the W-Diamond logo forged into the shank.

The overall length is 10.3 inches, and the finish is plain steel.

The inset shows a close-up of the stamped JHW-Brooklyn logo on the face.


864F S-Shaped Wrench With Concave Handle

In addition to the 66x series, Williams also produced an 86x series of heavy-duty S-shaped wrenches with concave handles. These were listed in the 1912 catalog as '"S" Wrenches with Concave Handles', and were available in sizes for both square toolpost nuts and hexagon head cap screws.

[Williams 864A 9/16x3/4 S-Shaped Wrench]
Fig. 39. Williams 864F 9/16x3/4 S-Shaped Wrench, with Inset for Reverse Detail.

Fig. 39 at the left shows a Williams 864A 9/16x3/4 S-shaped wrench, marked with the abbreviated variant of the JHW-Brooklyn logo on the face, and with the model number "864" forged into the shank. (The "F" suffix is stamped.) A forged-in W-Diamond logo also appears on the reverse shank.

The overall length is 7.2 inches, and the finish is plain steel.

The reverse faces are stamped "3/8" and "1/2" without a qualifier for the size convention, and in this case the sizes refer to the hex-head cap screw convention. More commonly an unqualified size would indicate a U.S.S. nut size, providing another example of the confusion associated with the older size conventions.


Other Tools


1729 "Ratcho" Open-End Wrench

Williams was one of the first companies to offer open-end wrenches with a ratcheting action, made possible by means of a special cut-away opening. These wrenches were covered by a 1910 patent and were sold under the "Ratcho" brand.

[Williams Ratcho 1729 5/8x3/4 Ratcheting Open-End Wrench]
Fig. 40. Williams "Ratcho" 1729 5/8x3/4 Ratcheting Open-End Wrench, with Inset for Reverse Detail, ca. 1910-1920.

Fig. 40 shows a rare Williams 1729 5/8x3/4 "Ratcho" open-end wrench, designed to give a ratcheting action in one direction. The shank has depressed panels with forged-in markings "J.H. Williams & Co." and "Brooklyn, N.Y. U.S.A." on the front, with "Ratcho Wrench" and "Patd. U.S.A. Apr. 26, '10" on the reverse.

The overall length is 6.6 inches, and the finish is plain steel.

The patent date corresponds to patent #956,259, filed by G. Amborn in 1908 and issued in 1910.


255A Socket Wrench

[Williams 255A 5/8 Socket Wrench]
Fig. 41. Williams 255A 5/8 Socket Wrench, with Inset for Marking Detail.

The overall length is 6.4 inches, and the finish is plain steel.


969A Offset Socket Wrench

[Williams 969A 5/8 Socket Wrench]
Fig. 42. Williams 969A 5/8 Socket Wrench, with Insets for Marking Detail.

Fig. 42 at the left shows a Williams 969A 7/8 offset socket wrench, stamped "J.H. Williams & Co." with "969A Offset" and the W-Diamond logo on the reverse. The bottom of the socket also has a forged-in "969A" model number.

The overall length is 7.8 inches, and the finish is plain steel.


Vulcan Auto Tool

[Williams Vulcan Auto Tool]
Fig. 43. Williams Vulcan Auto Tool, with Insets for Reverse Detail, ca. 1910-1915.

Fig. 43 shows the distinctive Williams "Vulcan Auto Tool", a combination tool for auto repair. The tool has forged-in markings "J.H. Williams & Co." and "Brooklyn, N.Y. U.S.A." with the W-Diamond logo, and the reverse is marked "Vulcan Auto Tool" and "Pat. Pendg." (see insets).

The overall length is 7.8 inches, and the finish is plain steel.

The patent corresponding to the pending notice has not yet been found.


No. 2 Bull Dog Wrench

Around 1920 Williams acquired the Whitman & Barnes Company, the maker of the well known "Bull Dog" line of alligator wrenches. Williams continued the production of the Bull Dog wrenches at least into the 1950s.

[Williams No. 2 Bull Dog Wrench]
Fig. 44. Williams No. 2 Bull Dog Wrench, with Inset for Reverse Detail.

Fig. 44 shows a Williams No. 2 "Bull Dog" wrench, a tool with serrated teeth in a tapered opening, sometimes called an alligator wrench. The shank has forged-in markings "Drop Forged in U.S.A." with the W-Diamond logo, with "J.H. Williams & Co." forged into the reverse.

The overall length is 9.1 inches, and the finish is plain steel.

The "Bull Dog" brand of alligator wrenches was originally produced by the Whitman & Barnes Company (W&B), which was acquired by J.H. Williams around 1920.


Alloy Artifacts Home Go To Page:  | 1 |   | 2 |   | 3 |   | 4 |   | 5 |   Next >> Site Index Contact Us